SIEMENS
7/143
Siemens D 21.4 · 2017
SINAMICS S120 drive system
Chassis format
Air-cooled Basic Line Modules in chassis format
7
■
Technical specifications
(continued)
Line voltage 380 ... 480 V 3 AC
Basic Line Modules
6SL3330-
1TE34-2AA3
6SL3330-
1TE35-3AA3
6SL3330-
1TE38-2AA3
6SL3330-
1TE41-2AA3
6SL3330-
1TE41-5AA3
6SL3330-
1TE41-8AA3
Rated power
• At
I
rated DC
(50 Hz 400 V)
kW
200
250
400
560
710
900
• At
I
H DC
(50 Hz 400 V)
kW
160
200
315
450
560
705
• At
I
rated DC
(60 Hz 460 V)
hp
305
385
615
860
1090
1390
• At
I
H DC
(60 Hz 460 V)
hp
245
305
485
690
860
1090
DC link current
• Rated current
I
rated DC
A
420
530
820
1200
1500
1880
• Base-load current
I
H DC
1)
A
328
413
640
936
1170
1467
• Maximum current
I
max DC
A
630
795
1230
1800
2250
2820
Input current
• Rated current
I
rated I
A
365
460
710
1010
1265
1630
• Maximum current
I
max I
A
547
690
1065
1515
1897
2380
• Max. pre-charging current (max. 3 s)
A
Internal
Internal
Internal
Internal
Internal
308
Current demand
• 24 V DC auxiliary power supply
A
1.1
1.1
1.1
1.1
1.1
1.1
DC link capacitance
• Basic Line Module
μ
F
7200
9600
14600
23200
29000
34800
• Drive line-up, max.
μ
F
57600
76800
116800
185600
232000
139200/278400
2)
Power loss, max.
3)
• At 50 Hz 400 V
kW
1.9
2.1
3.2
4.6
5.5
6.9
• At 60 Hz 460 V
kW
1.9
2.1
3.2
4.6
5.5
6.9
Cooling air requirement
m
3
/s (ft
3
/s)
0.17 (6.00)
0.17 (6.00)
0.17 (6.00)
0.36 (12.7)
0.36 (12.7)
0.36 (12.7)
Sound pressure level
L
pA
(1 m) at 50/60 Hz
dB
66/68
66/68
66/68
71/73
71/73
71/73
Line connection
U1, V1, W1
Flat connector
for M10 screw
Flat connector
for M10 screw
Flat connector
for M10 screw
Flat connector
for M12 screw
Flat connector
for M12 screw
Flat connector for
M12 screw
• Conductor cross section, max. (IEC)
mm
2
2 × 240
2 × 240
2 × 240
6 × 185
6 × 185
6 × 185
DC link connection
DCP, DCN
M10 screw
M10 screw
M10 screw
3 × hole for
M12
3 × hole for
M12
3 × hole for M12
• Conductor cross section, max. (IEC)
mm
2
2 × 240
2 × 240
2 × 240
6 × 185
6 × 185
6 × 185
PE/GND connection
2 × hole for
M10
2 × hole for
M10
2 × hole for
M10
2 × hole for
M12
2 × hole for
M12
2 × hole for M12
• Conductor cross section, max. (IEC)
mm
2
2 × 240
2 × 240
2 × 240
4 × 240
4 × 240
4 × 240
Cable length, max.
4)
• Shielded
m (ft)
2600 (8531)
2600 (8531)
2600 (8531)
4000 (13124)
4000 (13124)
4800 (15749)
• Unshielded
m (ft)
3900 (12796)
3900 (12796)
3900 (12796)
6000 (19686)
6000 (19686)
7200 (23623)
Degree of protection
IP00
IP00
IP00
IP00
IP00
IP00
Dimensions
• Width
mm (in)
310 (12.2)
310 (12.2)
310 (12.2)
310 (12.2)
310 (12.2)
310 (12.2)
• Height
mm (in)
1164 (45.8)
1164 (45.8)
1164 (45.8)
1653 (65.1)
1653 (65.1)
1653 (65.1)
• Depth
mm (in)
352 (13.9)
352 (13.9)
352 (13.9)
550 (21.6)
550 (21.6)
550 (21.6)
Weight, approx.
kg (lb)
96 (212)
96 (212)
96 (212)
214 (472)
214 (472)
214 (472)
Frame size
FB
FB
FB
GB
GB
GD
Minimum short-circuit current
5)
A
4400
5200
10000
12400
18400
18600
1)
The base-load current
I
H DC
is the basis for a duty cycle of 150 % for 60 s
or
I
max DC
for 5 s with a duty cycle duration of 300 s.
2)
The first value applies for one precharging resistor for each phase, the
second value for two precharging resistors connected in parallel for each
phase.
3)
The specified power loss represents the maximum value at 100 % utilization.
The value is lower under normal operating conditions.
4)
Total of all motor cables and DC link. Longer cable lengths for specific
configurations are available on request.
For additional information, please
refer to the SINAMICS Low Voltage Engineering Manual.
5)
Current required for reliably triggering protective devices.
© Siemens AG 2017